I have two LNBs connected via a DiSEqC switch - SPAUN SUR 211F DiSEqC 2.1. The two LNBs are pointing at Astra 19.2 and 28.2. there are three modes - 1st uncommitted switch, Position (Tone burst) and Option (only DiSEqC.For a better experience, please enable JavaScript in your browser before proceeding.With my satellite receiver the channels work just fine.Recently I tried to connect the satellite cable directly to my TV so see how it works.
Senderliste Samsung Astra Hotbird Settings Free Channels FromI got 500ish free channels from hotbird only and 0 from sirius. The next day I switched it on, the channels were there but I was getting weak or no signal while switching between the channels. I checked the cable from back of the TV and it was plugged properly. But after switching on the TV again after a while I get the same thing which is too strange. I went through all the LNB setting from the menu and set all the transponder parameters as I see them from my receiver, but. Most of them just wont get signal at all or get from 27-30 while when connected through the receiver I get mostly above 80. I would appreciate if anyone could help me on this to sort the things out. I found more time today and went trough the settings and set up the following. I have tried different combinations with DiSEqC settings. A and Tone B etc. I turned that ON and there are the following options: Positioner Type (options DiSEqC 1.2 and USALS) If you select USALS there are more options to select like: My Longitude ( X X Numbers to set and East or West) My Latitude ( X X Numbers and North or South) Satellite Longitude settings ( User sat 1 0.0 E, user sat 2 0.0 E, User sat 3 0.0 E, user sat 4 0.0 E to set) Sorry, for this essay, just tried to be as clear as possible. Then you should check on the satellite receiver what the correct DiSeqC settings are, and transfer those exactly to the TV. Run a Tune on each and let us know what kevkbuk asked about some of the channels received. Please explain further your comment about previously receiving Astra. The only thing that should need setting is the Diseqc mode for each sat, 14 to 44 depending on their position on the switch. You can get this from your receiver if you do not know, they may be alternatively labelled as A-D. You may find it has separate channel lists for each sat when viewing also. Both, Astra and HotBird channels are showing fine, although the signal on specific transponders drops sometimes to as low as 10-12. Senderliste Samsung Astra Hotbird Settings Full Mode ForI run AUTO tune in full mode for both of the satellites separately and found almost all the channels I needed except 5 of them. Senderliste Samsung Astra Hotbird Settings Manual Transponder SearchThen I tried to run manual transponder search which I have done in past 10-11 years on my receiver successfully, but the parameters I enter for the channels I need get 0 of signal, which is very weird, since they work fine on the receiver right now. The channels and parameters are as follows: ARM 1TV - HotBird 13E 12520V 27500 34 Armenia TV - HotBird 13E 12520V 27500 34 1TV RUS - HotBird 13E 12597V 27500 34 EuroNews (the multi language one I get on the receiver) - HotBird 13E 12597V 27500 34 RBC-TV - HotBird 12520V 27500 34 Again, thanks for the help. AK. I have two LNBs connected via a DiSEqC switch - SPAUN SUR 211F DiSEqC 2.1. The two LNBs are pointing at Astra 19.2 and 28.2. Position (Tone burst) and Option (only DiSEqC.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |